Unilift KP pumps are submersible drainage pumps suitable for both temporary and permanent free-standing installation. They can be used for pumping drain water or grey wastewater. They are also suitable for installation in collecting tanks.
The Unilift KP is a single-stage drainage pump with semi-open impeller, designed for the pumping of drain water and grey wastewater. All Unilift KP pumps can be supplied with or without a level switch. The variants are designated as A, AV or M, for automatic or manual operation. The Unilift KP-AV variant for narrow pits is supplied with a non-return flap valve for installation in the outlet. The strainer is clipped onto the pump housing.
The Unilift KP. Single-stage, submersible, stainless steel drainage pump in a robust design with upward-pointing discharge port positioned on the top of the pump.The outer casing is made in one piece. The mains cable and the cable of the level switch are both connected to a single, vulcanized, water-tight plug which is inserted in a socket on the hermetically-sealed stator housing. The motor is a single- or three-phase synchronous canned motor with liquid-filled rotor chamber and water-lubricated bearings.
The motor is cooled by the pumped liquid flowing around it.
- Enclosure class: IP 68
- Insulation class: F
The motor incorporates automatic overload protection which cuts out the motor in the event of overload. When it has cooled to normal temperature, the motor restarts automatically.
Applications
The Grundfos Unilift KP pumps are designed for the pumping of:
- Water and rainwater in horticulture
- Water from rivers and lakes
- Rainwater, drainage water and water from flooding
- Water for filling/emptying containers, ponds, tanks, etc.
- Effluents from showers, washing machines and sinks below sewer level
- Pool water
- Ditch drainage water
- Groundwater (lowering applications)
- Domestic effluents from septic and sludge-treating systems
- Effluents from viaducts, underpasses, etc.
- Drainage water from garage sprinkler systems.
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner
The SB pump is a submersible booster pump for the pumping of clean water. It is especially suitable for rainwater applications. The pump is available in two main versions:
- with integrated suction strainer (1 mm mesh)
- with side inlet which includes a flexible suction hose with floating suction strainer (1 mm mesh).
In both versions, the pump is available with or without float switch. The float switch can be used for automatic operation or dry-running protection of the pump.
Applications
The SB pump is a submersible booster pump for the pumping of clean water. It is especially suitable for rainwater applications.
Features and benefits
- Noiseless operation
- High reliability
- Integrated protection.
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner
The Grundfos DP pumps are designed for pumping drain water and groundwater from installations in or around private housing, farms and small industrial plants. These pumps are also ideal for flood-relief applications and as utility pumps in farming, industry, etc.
DP pumps are fitted with a suction strainer, on which the pump stands. The suction strainer allows for the passage of solid particles of up to 10 mm in size, which is the maximum free passage size through DP pumps. The strainer is easy to dismantle for cleaning or for inspection of the pump hydraulics.
The impeller for the DP range is of a semi-open multivane design. The impeller clearance can easily be adjusted simply by tightening or loosening the adjustment screws at the bottom of the suction cover.
Pumped liquids
The pumps are suitable for:
- Drainage and surface water
- Groundwater
- Industrial process water without solids or fibres.
Features and benefits
- Cable plug connection
- Unique clamp connection
- Specially designed lifting handle
- Unique cartridge shaft seal
- Modular design
- Heavy-duty ball bearings.
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner
Grundfos NK/NKG pumps are used in water supply, industrial pressure boosting, industrial liquid transfer, HVAC (heating, ventilation and air-conditioning), irrigation and process industries. Grundfos end-suction pumps are multi-purpose pumps suitable for a variety of different applications requiring reliable and cost-efficient supply. End-suction pumps are used in five main areas of application: water supply, industrial pressure boosting, industrial liquid transfer, HVAC (heating, ventilation and air-conditioning), and irrigation. The pumps are all non-self-priming, single-stage, centrifugal volute pumps with axial suction port, radial discharge port and horizontal shaft. The Grundfos NK/NKG range comprises a complete series of long-coupled pumps that comply fully with either EN733 or ISO2858. The pumps are of the back pull-out design, enabling removal of the motor, coupling, bearing bracket and impeller without disturbing the pump housing or pipework. Even the largest pumps can thus be serviced by one person with a crane. The ISO2858 range of pumps are available with a bearing life of 100,000 hours, and can be fitted with double seals. They available in a stainless steel version as an option.
Applications
Grundfos offers a virtually limitless range of long-coupled (NK) end-suction pumps. Their sturdiness and reliability make them ideal for use in demanding environments such as the following:
- District heating plants
- Heating systems for blocks of flats
- Air-conditioning systems
- Cooling systems
- Wash down systems
- Other industrial systems.
Features and benefits
- Optimised hydraulics in housing and impeller = unimpeded liquid flow
- O-ring seal between pump housing and cover = no risk of leakage
- Housing, impeller and wear ring in different materials = improved corrosion resistance, no sticking elements
- Back pull-out design for easy dismantling for service
- Pump is electro-coated to increase corrosion resistance
- Available with IE1, IE2 and IE3 motors
- PN 10/16 and 25 bar
- Temperatures up to 180 °C
- Available in a number of shaft seal and material variants.
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner LEADER Pump
Grundfos RC pumps are used for the circulation of liquid refrigerants in refrigeration systems.
The RC pumps have been designed and optimised for use with CO2 as a refrigerant, but can also be used with NH3 (Ammonia) and selected HFCs.
The low required NPSH and the fact that no traditional loss-generating protective devices are needed can help system designers to reduce the dimensions and cost of the system. The RC pumps have an innovative design in stainless steel which makes specially suited for use with high pressure refrigerants (CO2) – the pump has only one seal between the refrigerant and ambient sides. A version with welded connections eliminates the use of counter flanges and possible leakage in flange connections.
Applications
Grundfos RC pumps are designed for the circulation of liquid refrigerant in refrigeration systems.
Features and benefits
- Barrel-type, semi-hermetic, high-pressure design
- Multistage centrifugal pump
- Canned motor (no shaft seals)
- High energy efficiency
- Wide range for variable speed capacity control
- Low NPSHR and robust to vapour bubbles in inlet
- Installation and service friendly
- Compact and low weight.
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner LEADER Pump
Backwashing refers to the reverse-pumping of water, for example for the periodic washing of filters. Grundfos can supply pumping solutions that deliver the very strong force with well-executed flush times and speeds required for effective backwashing.
Backwashing is a form of preventive maintenance to prevent further clogging of the filter medium. Backwashing in water treatment plants is an automated process, usually run by programmable logic controllers (PLCs). The backwash cycle is usually triggered when the differential pressure over the filter exceeds a set value.
Grundfos can supply pumping solutions to cope with the hugely varying flow requirements for backwashing, ranging from huge split-case and mixed-flow pumps, where the focus is on moving water rather than added pressure, to our highly successful vertical multistage centrifugal pump (CR) – and covering all performance requirements in between.
Grundfos can supply the specialist expertise to help meet your performance objectives, from the initial identification of needs, to the selection, installation, operation, and maintenance of the pumping solution. Grundfos commissioning agreements ensure correct installation and service agreements cover all eventualities, from routine maintenance to spare parts and pump audits.
The durietta 0 is a close-coupled, end-suction, single-stage or multistage centrifugal pump suitable for all kinds of low-flow, high-head applications requiring sanitary pumping equipment. The pump is designed in compliance with food technology requirements, making it ideal for applications where a high level of hygiene is required. It is CIP- and SIP-capable, and in line with the performance characteristics outlined for pumps in DIN 12462.
The durietta 0 is made from high-quality stainless steel to ensure reliable, hygienic, non-corrosive operation. Stages, discharge and suction casings, and impellers are manufactured from deep-drawn rolled stainless steel.
Applications
- Liquid transfer in breweries and dairies
- Mixing and soft drink applications
- Food processing plants
- Filtration and bottling systems
- CIP (Cleaning-In-Place) systems
- Process pumping in the chemical industry
- As a transfer and circulation pump in water treatment systems
- Virtually all types of transfer, circulating and process pumping
Features and benefits
- Designed for sanitary applications
- Easy service and maintenance, modular design
- Reliable – less downtime
- High efficiency and low energy consumption
- Compact design
- CIP and SIP capable (DIN EN 12462)
- Materials: Rolled, deep-drawn steel AISI 316L (1.4404) with electropolished surface
- Gentle liquid handling for sensitive liquids
- Optimised hydraulics
- Single and double mechanical seals in tandem
- Shrouded pumps, especially useful for breweries and dairies
- Various pipe connection types and connection sizes
- Designed for low-flow, high-head applications
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner
The SB and SBA pump is a submersible booster pump for the pumping of clean water. It is especially suitable for rainwater applications and private wells. The pump is available in two versions:
SB
The Grundfos SB is a submersible pump for the pumping of clean water. It is designed for use in domestic applications. The pump itself is very silent, and when installed underground in a rainwater collecting tank or well, noise will never become an issue. The SB pump requires an external controller, like Pressure Manager, for automatic operation.
Features and benefits
- Flexible selection – Pump + controller
- Complete control and monitoring
- Easily accessible controller – for service & replacement
SBA
The new Grundfos SBA is a complete all-in-one unit. It is built on the proven SB platform, but comes with an integrated control unit – eliminating the need for an external pump controller.
The SBA is literally a plug- and pump solution. Once installed and connected to the piping, all you need to do is switch on the pump.
Features and benefits
- Easy selection – one unit
- Easy installation – one unit
- Flexible installation – no controller inside the house
All SB and SBA pumps are available in two main variants
- With integrated suction strainer (1 mm mesh)
- Or with side inlet/flexible suction hose with floating suction strainer (1 mm mesh).
All variants are available with or without float switch:
The float switch offers automatic operation and dryrun protection, stop at low water level, ensuring that surface fragments do not enter the strainer.
Applications
The SB and SBA pump is a submersible booster pump for the pumping of clean water. It is especially suitable for rainwater applications.
Features and benefits
- Noiseless operation
- High reliability
- Integrated protection.
- Floating suction strainer
The model with floating suction strainer always draws the water from just below the water surface where the water is clean and free from solid particles.
Additional features of the SBA:
- Simplicity – all-in-one unit
- Easy installation – no external control unit
- Integrated dry-running protection
- Automatic restart after dry-running
- Lifting eye
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner LEADER Pump
DWK and DPK are submersible pumps designed for dewatering and drainage applications. The cast-iron construction and the hydraulic design contribute durability and high efficiency. The differences between the DWK and DPK pump ranges lie in the discharge arrangement and the installation type. The DWK is designed with a top discharge pipe and suction strainer, and is thus more suitable for temporary installation, whereas the DPK has a side discharge and a ring-stand or auto coupling (as accessories), and is suitable for permanent installations.
Applications
DWK/DPK are excellent pumps for dewatering and draining applications. The combination of compact design with high-pressure capability makes the pumps suitable for use in pits, whether for temporary or fixed installation. The installation design options provide the flexibility needed to cover many needs. Applications include:
- Construction sites
- Excavations
- Tunnels
- Fish ponds
- Drainage pits.
Features and benefits
- Durability
- High efficiency
- Installation flexibility
- High-pressure capabilities, cost-effectiveness
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner
Backwashing refers to the reverse-pumping of water, for example for the periodic washing of filters. Grundfos can supply pumping solutions that deliver the very strong force with well-executed flush times and speeds required for effective backwashing.
Backwashing is a form of preventive maintenance to prevent further clogging of the filter medium. Backwashing in water treatment plants is an automated process, usually run by programmable logic controllers (PLCs). The backwash cycle is usually triggered when the differential pressure over the filter exceeds a set value.
Grundfos can supply pumping solutions to cope with the hugely varying flow requirements for backwashing, ranging from huge split-case and mixed-flow pumps, where the focus is on moving water rather than added pressure, to our highly successful vertical multistage centrifugal pump (CR) – and covering all performance requirements in between.
Grundfos can supply the specialist expertise to help meet your performance objectives, from the initial identification of needs, to the selection, installation, operation, and maintenance of the pumping solution. Grundfos commissioning agreements ensure correct installation and service agreements cover all eventualities, from routine maintenance to spare parts and pump audits.
PT. Andalan Inti Rekatama – GRUNDFOS Authorized Dealer – Service Partner
