The Grundfos HS horizontal split case pump is a single-stage, non-self-priming, between bearing, centrifugal volute pump. The axially split design allows easy removal of the top casing and access to the pump components (bearings, wear rings, impeller, and shaft seal) without disturbing the motor or pipework.

The independent bearing housing allows for ease of maintenance without removing the top casing. The double volute design reduces the radial load on the shaft, extending component life, minimising vibration and providing quiet operation.

The HS pump also offers high pump efficiencies throughout the range.  High energy efficiency along with long pump life and easy maintenance add up to low life-cycle costs.
The HS pump is available in three configurations – pump with motor and baseframe, pump with baseframe, and bare shaft pump only.
The HS pump is ideal for custom applications and is available in a wide range of variants. The high efficiency and low life cycle costs make the HS ideal for any commercial building, water utility or industrial project.

Applications

Grundfos HS horizontal split case pumps are typically used in these applications:

• Air-conditioning/heating systems
• Public water supply
• District cooling/heating plants
• Cooling systems
• Public waterworks
• Process cooling
• Irrigation.

Features and benefits

• Easy to service: split case design
• Double suction minimises axial load,which extends the life of the wear rings, shaft seals and bearings
• Double volute reduces radial forces and minimises noise and vibration
• Independent bearing housing design allows access to the pump components without removing the top half of the casing
• High energy efficiency
• Low life-cycle costs
• Many product variants available.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Grundfos HS horizontal split case pump is a single-stage, non-self-priming, between bearing, centrifugal volute pump. The axially split design allows easy removal of the top casing and access to the pump components (bearings, wear rings, impeller, and shaft seal) without disturbing the motor or pipework.

The independent bearing housing allows for ease of maintenance without removing the top casing. The double volute design reduces the radial load on the shaft, extending component life, minimising vibration and providing quiet operation.

The HS pump also offers high pump efficiencies throughout the range.  High energy efficiency along with long pump life and easy maintenance add up to low life-cycle costs.

The HS pump is available in three configurations – pump with motor and baseframe, pump with baseframe, and bare shaft pump only.

The HS pump is ideal for custom applications and is available in a wide range of variants. The high efficiency and low life cycle costs make the HS ideal for any commercial building, water utility or industrial project.

Applications

Grundfos HS horizontal split case pumps are typically used in these applications:

• Air-conditioning/heating systems
• Public water supply
• District cooling/heating plants
• Cooling systems
• Public waterworks
• Process cooling
• Irrigation.

Features and benefits

• Easy to service: split case design
• Double suction minimises axial load,which extends the life of the wear rings, shaft seals and bearings
• Double volute reduces radial forces and minimises noise and vibration
• Independent bearing housing design allows access to the pump components without removing the top half of the casing
• High energy efficiency
• Low life-cycle costs
• Many product variants available.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Grundfos HS horizontal split case pump is a single-stage, non-self-priming, between bearing, centrifugal volute pump. The axially split design allows easy removal of the top casing and access to the pump components (bearings, wear rings, impeller, and shaft seal) without disturbing the motor or pipework.

The independent bearing housing allows for ease of maintenance without removing the top casing. The double volute design reduces the radial load on the shaft, extending component life, minimising vibration and providing quiet operation.

The HS pump also offers high pump efficiencies throughout the range.  High energy efficiency along with long pump life and easy maintenance add up to low life-cycle costs.
The HS pump is available in three configurations – pump with motor and baseframe, pump with baseframe, and bare shaft pump only.
The HS pump is ideal for custom applications and is available in a wide range of variants. The high efficiency and low life cycle costs make the HS ideal for any commercial building, water utility or industrial project.

Applications

Grundfos HS horizontal split case pumps are typically used in these applications:

• Air-conditioning/heating systems
• Public water supply
• District cooling/heating plants
• Cooling systems
• Public waterworks
• Process cooling
• Irrigation.

Features and benefits

• Easy to service: split case design
• Double suction minimises axial load,which extends the life of the wear rings, shaft seals and bearings
• Double volute reduces radial forces and minimises noise and vibration
• Independent bearing housing design allows access to the pump components without removing the top half of the casing
• High energy efficiency
• Low life-cycle costs
• Many product variants available.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Grundfos HS horizontal split case pump is a single-stage, non-self-priming, between bearing, centrifugal volute pump. The axially split design allows easy removal of the top casing and access to the pump components (bearings, wear rings, impeller, and shaft seal) without disturbing the motor or pipework.

The independent bearing housing allows for ease of maintenance without removing the top casing. The double volute design reduces the radial load on the shaft, extending component life, minimising vibration and providing quiet operation.
The HS pump also offers high pump efficiencies throughout the range.  High energy efficiency along with long pump life and easy maintenance add up to low life-cycle costs.
The HS pump is available in three configurations – pump with motor and baseframe, pump with baseframe, and bare shaft pump only.
The HS pump is ideal for custom applications and is available in a wide range of variants. The high efficiency and low life cycle costs make the HS ideal for any commercial building, water utility or industrial project.

Applications

Grundfos HS horizontal split case pumps are typically used in these applications:

• Air-conditioning/heating systems
• Public water supply
• District cooling/heating plants
• Cooling systems
• Public waterworks
• Process cooling
• Irrigation.

Features and benefits

• Easy to service: split case design
• Double suction minimises axial load,which extends the life of the wear rings, shaft seals and bearings
• Double volute reduces radial forces and minimises noise and vibration
• Independent bearing housing design allows access to the pump components without removing the top half of the casing
• High energy efficiency
• Low life-cycle costs
• Many product variants available.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

Pressure Booster : Grundfos Hydro MPC

Grundfos has developed the perfect brains for use with CR-based Hydro booster systems. The Multi Pump Control ( MPC ) maintains its outstanding user friendliness right from the initial installation through to everyday operation.

The large display is easy to navigate, regardless of whether you are using the installation wizard or carrying out day – to – day monitoring. The Ethernet connection option even brings the Hydro MPC interface to your own computer so that matter where you are, you will always be in control.

The Hydro MPC can control up to six pumps connected in parallel, adjusting the speed of each pump to optimize performance at all times.

The Hydro MPC also gives you access to remote data communication, operation statistics, and mauch more.

Features and benefits
– Constant pressure
– Simple installation
– Low-energy
– Wide range

Optional:
– External communication, Control 2000

Applications
Hydro 2000 are suitable for pressure boosting in
– Water supply systems
– Irrigation systems
– Water treatment systems
– Fire fighting systems
– Industrial plants

Technical Data
– Flow Q: max. 720 m3/h
– Head, H: max. 160 m
– Liquid temp.: 0oC to +70oC

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner  – Grundfos Booster Hydro MPC

Grundfos Hydro MPC – Booster set

Hydro MPC booster sets consist of two to six identical CRI(E)/CR(E) pumps connected in parallel and mounted on a common base frame provided with a control cabinet and all the necessary fittings.

As standard, Hydro MPC booster sets consist of two to six identical CRI(E)/CR(E) pumps connected in parallel and mounted on a common base frame provided with a control cabinet and all the necessary fittings.

Hydro MPC booster sets are supplied as complete, pre-assembled and thoroughly tested booster sets, ready to install.

Most of the booster sets are available with either CR(I) pumps and/or CR(I)E pumps.

Hydro MPC booster sets are divided into seven groups based on control variants.

Hydro MPC’s outstanding reliability and efficiency is the best possible base for our booster systems. Equipped with the intelligent CU 351 controller, the Hydro MPC boosters offer an even higher efficiency and reduced energy costs. The end result is complete control, optimum flexibility of booster output, and unbeatable efficiency at all times.

Hydro MPC booster sets are fitted with hygienic designed manifolds.

Water Supply

Grundfos Hydro MPC boosters are ideal for mains water supply systems and for pressure boosting in multi-storey buildings. The needs for water in multi storey buildings vary a lot during the course of the day – this demands much from the equipment used. With a Grundfos booster system, it is easy to provide optimum user comfort by maintaining constant water pressure at all levels and at all times.

Industry

Industries can also benefit greatly from a booster solution from Grundfos. If you require constant pressure in the face of highly variable flows, Grundfos has the solution. Even the most demanding applications will benefit from the accuracy and advanced pump control in a Grundfos Hydro MPC booster.

Irrigation

A Grundfos Hydro MPC booster system can help conserve water and optimise crop yields by responding to pre-set minimum and maximum levels. Grundfos Hydro MPC is lenient on the pipe net in golf course irrigation systems and adapts the performance automatically to any number of sprinklers at any pressure zone during the irrigation cycle. It is benefits like these that make Grundfos the perfect choice for irrigation systems.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner  – Grundfos Booster Hydro MPC

The Grundfos HS horizontal split case pump is a single-stage, non-self-priming, between bearing, centrifugal volute pump. The axially split design allows easy removal of the top casing and access to the pump components (bearings, wear rings, impeller, and shaft seal) without disturbing the motor or pipework.

The independent bearing housing allows for ease of maintenance without removing the top casing. The double volute design reduces the radial load on the shaft, extending component life, minimising vibration and providing quiet operation.

The HS pump also offers high pump efficiencies throughout the range.  High energy efficiency along with long pump life and easy maintenance add up to low life-cycle costs.
The HS pump is available in three configurations – pump with motor and baseframe, pump with baseframe, and bare shaft pump only.
The HS pump is ideal for custom applications and is available in a wide range of variants. The high efficiency and low life cycle costs make the HS ideal for any commercial building, water utility or industrial project.

Applications

Grundfos HS horizontal split case pumps are typically used in these applications:

• Air-conditioning/heating systems
• Public water supply
• District cooling/heating plants
• Cooling systems
• Public waterworks
• Process cooling
• Irrigation.

Features and benefits

• Easy to service: split case design
• Double suction minimises axial load,which extends the life of the wear rings, shaft seals and bearings
• Double volute reduces radial forces and minimises noise and vibration
• Independent bearing housing design allows access to the pump components without removing the top half of the casing
• High energy efficiency
• Low life-cycle costs
• Many product variants available

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Grundfos HS horizontal split case pump is a single-stage, non-self-priming, between bearing, centrifugal volute pump. The axially split design allows easy removal of the top casing and access to the pump components (bearings, wear rings, impeller, and shaft seal) without disturbing the motor or pipework.
The independent bearing housing allows for ease of maintenance without removing the top casing. The double volute design reduces the radial load on the shaft, extending component life, minimising vibration and providing quiet operation.

The HS pump also offers high pump efficiencies throughout the range.  High energy efficiency along with long pump life and easy maintenance add up to low life-cycle costs.
The HS pump is available in three configurations – pump with motor and baseframe, pump with baseframe, and bare shaft pump only.
The HS pump is ideal for custom applications and is available in a wide range of variants. The high efficiency and low life cycle costs make the HS ideal for any commercial building, water utility or industrial project.

Applications

Grundfos HS horizontal split case pumps are typically used in these applications:

• Air-conditioning/heating systems
• Public water supply
• District cooling/heating plants
• Cooling systems
• Public waterworks
• Process cooling
• Irrigation.

Features and benefits

• Easy to service: split case design
• Double suction minimises axial load,which extends the life of the wear rings, shaft seals and bearings
• Double volute reduces radial forces and minimises noise and vibration
• Independent bearing housing design allows access to the pump components without removing the top half of the casing
• High energy efficiency
• Low life-cycle costs
• Many product variants available.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

Grundfos TP and TPE vertical in-line volute pumps are used in a variety of applications. The pumps are all single-stage, in-line centrifugal volute pumps with standard motors and mechanical shaft seals. The pumps are of the close-coupled type, i.e. pump and motor are separate units. Consequently, the pumps are less sensitive to impurities in the pumped liquid than similar pumps of the canned rotor type.

Two different models of vertical in-line volute pumps are available. Please note that there are a number of specific product variants available for each model. Detailed information on these variants can be found in Grundfos WebCAPS.

TP pump

This pump model is notable for its high levels of reliability and efficiency.  Quiet, highly-efficient IE3 motors are standard components. All TP pumps are electro-coated to ensure high corrosion resistance.

TPE pump

The main difference between TP and TPE pumps is the motor. TPE motors have a built-in frequency converter, allowing different control methods to be employed. TPE pumps offer benefits with respect to energy savings and increased comfort.

Applications

These vertical in-line volute pumps are used in commercial buildings for air conditioning and heating applications.

The pumps are all single-stage, in-line centrifugal volute pumps with standard motors and mechanical shaft seals. The pumps are of the close-coupled type, i.e. pump and motor are separate units. Consequently, the pumps are less sensitive to impurities in the pumped liquid than similar pumps of the canned rotor type.

Features and benefits

• Optimised hydraulics for high efficiency

• Reduced power consumption

• High-efficiency motors

• TP pumps are fitted with high-efficiency motors
• High-efficiency motors provide reduced energy consumption
• 2-pole and 4-pole TP pumps from 0.75 kW to 375 kW have IE3 motors (By March 2012)

• Top-pull-out design

• Easy dismantling for service

• In-line design

• Unlike end-suction pumps, in-line pumps allow the use of straight pipework, which often results in reductions in installation cost and amount of space occupied

• Hydraulically and mechanically balanced impeller (Series 300 and 400)

• The impeller is hydraulically and mechanically balanced to increase the life of motor bearings and shaft seals

• Pump housing and pump head/motor stool are electro-coated

• Improved corrosion resistance

• TPE, TPED – pumps with built-in frequency converter

• Reduced power consumption

• TPE and TPED motors are based on IE3 motors (except 18.5, 4-pole).