The Unilift CC is a single-stage submersible drainage pump, designed for the pumping of drain water and grey wastewater. The Unilift CC can pump down to a water level of 3 mm above the floor by removing the strainer. The Unilift CC is suitable for permanent as well as temporary installation. The Unilift CC is fitted with a non-return flap valve in the outlet in order to prevent backflow from the piping system. An adaptor ensures good connections to 3/4”, 1” or 1 1/4” outlets.

The strainer is made of stainless steel, while the main pump parts, e.g. the sleeve and pump housing, are made of moulded composite materials.

The Multibox B-CC7 is an Unilift CC combined with further elements such as a hose with Storz coupling, an adaptor for threaded Storz coupling and a box with perforated-mesh sides to be used as a pre-strainer for the pump. It is the perfect solution for use as an emergency kit for single family houses in the event of flooding.

Applications

The Unilift CC is designed for the pumping of the following:

• Water and rainwater in horticulture
• Water from rivers and lakes
• Rainwater, drainage water and water from flooding
• Water for filling/emptying containers, ponds, tanks, etc.
• Effluents from showers, washing machines and sinks below sewer level
• Pool water
• Ditch drainage water
• Groundwater (lowering applications)
• Effluents from viaducts, underpasses, etc.
• Drainage water from garage sprinkler systems.

Features and benefits

• Composite materials
• Stainless steel strainer
• Self-venting valve in handle
• Available with level switch
• Suitable for low suction levels
• Light-weight.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The basic CR pump range, which can be applied in almost any industrial solution, is already in itself the broadest range available. Through our modular approach, we have made it even broader.

The basic CR pump range is available in four different materials: cast iron, two grades of stainless steel, and all-titanium. There are eleven flow sizes, capable of producing up to almost 50 bar of pressure, and with a variety of shaft seals, rubber materials and supply voltages.

Pump parts which are typically vulnerable to difficult liquids or particularly demanding operating conditions can be optimised for their purpose and designed for specific requirements.

Applications

CR pumps provide a complete range of pump solutions so that all applications, industrial and domestic, can benefit from the Grundfos touch. The applications that can be covered include the following:

• Process water systems
• Washing and cleaning systems
• Seawater systems
• Pumping of acids and alkalis
• Ultrafiltration systems
• Reverse osmosis systems
• Swimming baths.

Features and benefits

• Reliability
• High efficiency
• Service-friendly
• Space-saving
• Suitable for slightly aggressive liquids
• High corrosion resistance
• Single-pump solution making high pressures possible.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The SEG range of grinder pumps from Grundfos is specifically designed for pumping effluent and untreated sewage in small communities or sparsely populated areas with no sewer systems or where gravitation systems are unsuitable.

Pressurised systems are the perfect choice for transfer of effluent and sewage, and the SEG range combines cost-effectiveness with maximum protection for the environment by facilitating the use of smaller pressure pipes for minimal investment costs.

The SEG range is designed to reduce energy consumption and to keep downtime costs to a minimum, while maintaining peak performance throughout the system life.

Applications

The Grundfos SEG pumps are specifically designed for pumping untreated wastewater from domestic, commercial or municipal sources. The high discharge pressure enables transfer of wastewater over longer distances.

Features and benefits

• Cable plug connection
• Efficient grinder system
• SmartTrim impeller adjustment
• Unique clamp connection
• Specially designed lifting handle
• Unique cartridge shaft seal
• Modular design
• Heavy-duty ball bearings.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

S pumps form the backbone of many sewage systems. They are selected for their strength, their durability, and for innovative features such as the SmartTrim impeller clearance adjustment system and the Smart Seal for leakage prevention.

The SmartTrim system used on the S-pumps makes it easy to adjust the factory-set impeller clearance and thus to maintain maximum pump efficiency.

The Grundfos SmartSeal Auto-coupling gasket provides a completely leak-proof connection between the pump and the base unit of the auto-coupling system. The shaft seal is capable of rotating in either direction. When the pumps are installed with separate pipework, sludge sedimentation can be avoided by back-flushing the system at regular intervals.

Applications

The pumps are suitable for the following applications:

• Transfer of unscreened raw sewage
• Transfer of raw water
• Pumping of water containing sludge
• Pumping of industrial effluent.

Features and benefits

• Wide range
• SmartTrim
• Operation with/without cooling jacket
• Submerged or dry installation
• Channel and vortex impellers
• Built-in motor protection
• SmartSeal
• Large free passage
• SuperVortex impeller.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Unilift AP and Unilift AP Basic are submersible drainage pumps designed for both temporary/portable installation and permanent free-standing installation. These single-stage pumps are made mostly of stainless steel. All types are available in either single phase or three phase versions and for 50 or 60 Hz power supply.

The number in the type designation, e.g. AP12, indicates the spherical particle size that can pass through the pump.

All Unilift AP and AP Basic pumps are fitted with a plug for connection to the mains.

Unilift AP is a single stage pump with either semi-open impeller (AP12) or with vortex impeller (AP35 and AP50). All Unilift AP pumps are fitted with a stainless steel sleeve for cooling during operation. The strainer at the bottom prevents particles larger than the pump is designed for from entering the pump. The strainer is clipped onto the pump housing. All Unilift AP pumps can be supplied with or without float switch, for automatic or manual operation. Pumps with an ”A” in the type designation are fitted with a float switch. 3-phase versions have an additional starter box connected to the float switch. The outlet is positioned at the top of the pump and is available in Rp 1 1/2 to Rp 2.

An optional non-return flap valve can be fitted in the outlet in order to prevent backflow.

Unilift AP Basic pumps are single-stage pumps (AP35B, AP50B) with vortex impeller. All Unilift AP Basic pumps are made of stainless steel, with a composite baseplate. The Unilift AP Basic range is designed for submerged operation, either free-standing on the base plate or installed using an auto coupling. The pump inlet is designed to prevent to large particles from entering the pump. The base plate is clipped on by means of four clips hidden under the composite ring at top of the pump housing. The ring prevents dirt from sticking to the clips. All Unilift AP Basic pumps can be supplied with or without float switch, for automatic or manual operation. Pumps with an ”A” in the type designation are fitted with a float switch. The outlet is positioned at the side of the pump and is R 2.

Applications

• Water and rainwater in horticulture
• Water from rivers and lakes
• Rainwater, drainage water and water from flooding
• Water for filling/emptying containers, ponds, tanks, etc.
• Effluents from showers, washing machines and sinks below sewer level
• Pool water
• Ditch drainage water
• Groundwater (lowering applications)
• Domestic effluents from septic and sludge-treating systems
• Liquids containing fibres from light industry, laundries, etc.
• Effluents from viaducts, underpasses, etc.
• Drainage water from garage sprinkler systems

Features and benefits

Unilift AP is for permanent or temporary free-standing installations. Most components are made of stainless steel. Cable fitted by means of a plug. Available in both automatic and manual versions. Single-phase versions have an integrated thermal switch.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

DWK and DPK are submersible pumps designed for dewatering and drainage applications. The cast-iron construction and the hydraulic design contribute durability and high efficiency. The differences between the DWK and DPK pump ranges lie in the discharge arrangement and the installation type. The DWK is designed with a top discharge pipe and suction strainer, and is thus more suitable for temporary installation, whereas the DPK has a side discharge and a ring-stand or auto coupling (as accessories), and is suitable for permanent installations.

Applications

DWK/DPK are excellent pumps for dewatering and draining applications. The combination of compact design with high-pressure capability makes the pumps suitable for use in pits, whether for temporary or fixed installation. The installation design options provide the flexibility needed to cover many needs. Applications include:

• Construction sites
• Excavations
• Tunnels
• Fish ponds
• Drainage pits.

Features and benefits

• Durability
• High efficiency
• Installation flexibility
• High-pressure capabilities, cost-effectiveness.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Unilift CC is a single-stage submersible drainage pump, designed for the pumping of drain water and grey wastewater. The Unilift CC can pump down to a water level of 3 mm above the floor by removing the strainer. The Unilift CC is suitable for permanent as well as temporary installation. The Unilift CC is fitted with a non-return flap valve in the outlet in order to prevent backflow from the piping system. An adaptor ensures good connections to 3/4”, 1” or 1 1/4” outlets.

The strainer is made of stainless steel, while the main pump parts, e.g. the sleeve and pump housing, are made of moulded composite materials.

The Multibox B-CC7 is an Unilift CC combined with further elements such as a hose with Storz coupling, an adaptor for threaded Storz coupling and a box with perforated-mesh sides to be used as a pre-strainer for the pump. It is the perfect solution for use as an emergency kit for single family houses in the event of flooding.

Applications

The Unilift CC is designed for the pumping of the following:

• Water and rainwater in horticulture
• Water from rivers and lakes
• Rainwater, drainage water and water from flooding
• Water for filling/emptying containers, ponds, tanks, etc.
• Effluents from showers, washing machines and sinks below sewer level
• Pool water
• Ditch drainage water
• Groundwater (lowering applications)
• Effluents from viaducts, underpasses, etc.
• Drainage water from garage sprinkler systems.

Features and benefits

• Composite materials
• Stainless steel strainer
• Self-venting valve in handle
• Available with level switch
• Suitable for low suction levels
• Light-weight.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

Grundfos SP submersible pumps are renowned for their high efficiency and reliability throughout the range. Made entirely of corrosion-resistant stainless steel, SP pumps are ideal for a wide variety of applications.

Grundfos SP pumps represent state-of-the-art hydraulic design. Built to deliver optimum efficiency during periods of high demand, the SP pumps provide low long-term costs and high operating reliability regardless of the application.

The Grundfos SP range offers high efficiency, high resistance to sand and other abrasives, motor burnout protection, and easy maintenance. A complete monitoring and control system is available for constant optimisation of the pumping system.

Applications

The pumps are suitable for:

• Groundwater supply to waterworks
• Irrigation in horticulture and agriculture
• Groundwater lowering
• Pressure boosting
• Industrial applications.

Features and benefits

• State-of-the-art hydraulics provide high efficiency and low operating costs
• 100 % stainless steel inside and outside
• Sand resistant
• Resistant to aggressive water
• Motor burnout protection
• Dry-running protection
• Monitoring, protection and communication via the MP 204 protection unit and the R100 remote control.