Grundfos RC pumps are used for the circulation of liquid refrigerants in refrigeration systems.

The RC pumps have been designed and optimised for use with CO₂ as a refrigerant, but can also be used with NH₃ (Ammonia) and selected HFCs.

The low required NPSH and the fact that no traditional loss-generating protective devices are needed can help system designers to reduce the dimensions and cost of the system. The RC pumps have an innovative design in stainless steel which makes specially suited for use with high pressure refrigerants (CO₂) – the pump has only one seal between the refrigerant and ambient sides. A version with welded connections eliminates the use of counter flanges and possible leakage in flange connections.

Applications

Grundfos RC pumps are designed for the circulation of liquid refrigerant in refrigeration systems.

Features and benefits

• Barrel-type, semi-hermetic, high-pressure design
• Multistage centrifugal pump
• Canned motor (no shaft seals)
• High energy efficiency
• Wide range for variable speed capacity control
• Low NPSHR and robust to vapour bubbles in inlet
• Installation and service friendly
• Compact and low weight.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

Unilift KP pumps are submersible drainage pumps suitable for both temporary and permanent free-standing installation. They can be used for pumping drain water or grey wastewater. They are also suitable for installation in collecting tanks.

The Unilift KP is a single-stage drainage pump with semi-open impeller, designed for the pumping of drain water and grey wastewater. All Unilift KP pumps can be supplied with or without a level switch. The variants are designated as A, AV or M, for automatic or manual operation. The Unilift KP-AV variant for narrow pits is supplied with a non-return flap valve for installation in the outlet. The strainer is clipped onto the pump housing.

The Unilift KP. Single-stage, submersible, stainless steel drainage pump in a robust design with upward-pointing discharge port positioned on the top of the pump.The outer casing is made in one piece. The mains cable and the cable of the level switch are both connected to a single, vulcanized, water-tight plug which is inserted in a socket on the hermetically-sealed stator housing. The motor is a single- or three-phase synchronous canned motor with liquid-filled rotor chamber and water-lubricated bearings.

The motor is cooled by the pumped liquid flowing around it.

• Enclosure class: IP 68
• Insulation class: F

The motor incorporates automatic overload protection which cuts out the motor in the event of overload. When it has cooled to normal temperature, the motor restarts automatically.

Applications

The Grundfos Unilift KP pumps are designed for the pumping of:

• Water and rainwater in horticulture
• Water from rivers and lakes
• Rainwater, drainage water and water from flooding
• Water for filling/emptying containers, ponds, tanks, etc.
• Effluents from showers, washing machines and sinks below sewer level
• Pool water
• Ditch drainage water
• Groundwater (lowering applications)
• Domestic effluents from septic and sludge-treating systems
• Effluents from viaducts, underpasses, etc.
• Drainage water from garage sprinkler systems.

The JP pump is a self-priming, single-stage centrifugal pump with axial suction port and radial discharge port, G 1 or Rp 1. The pump has a built-in ejector with guide vanes for optimum self-priming properties.

JP pumps are available in two material variants.

Material variant A: Cover plate, motor stool and base plate in one unit. The handle is fitted crosswise. Both elements are made of composite material.

Material variant B: Stainless steel cover plate, aluminium motor stool and stainless steel base plate, all separate parts.

The robust design makes the pump suitable for fixed installation. The custom-built composite handle is fitted lengthwise.

The pump is directly coupled to a special fan-cooled asynchronous Grundfos motor that is adapted to the pump performance Single-phase motors have a built-in thermal switch and require no additional motor protection Three-phase motors require external motor protection

Applications

Built for a long, trouble-free working life, the small and handy Grundfos jet pump is suitable for a wide variety of water supply and transfer duties in home, garden and hobby applications as well as in agriculture, horticulture and small-scale service industries.

When used in combination with a pressure control or tank, the JP pump is ideal for small water supply systems.

Features and benefits

• Self-priming
• Stable operation even if there is air in the liquid
• Ideal for small water supply systems
• Compact and handy.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

Grundfos EF pumps are designed for pumping wastewater (excluding toilet waste) from private dwellings. They are also suitable for pumping liquid manure from farms, and for a variety of industrial applications.

The EF pumps are designed for free-standing, hook-up or auto-coupling installation. The pumps are fitted with an integrated three-legged stand. They are capable of handling liquids containing solids of up to 30 mm in size.

The Grundfos EF pumps are fitted with an open single-vane impeller with excellent solids-handling capabilities.

Impeller clearance can be adjusted by tightening or loosening the adjustment screws at the bottom of the suction cover. Adjustment can be carried out without dismantling the pump.

Applications

The pumps are suitable for:

• Drainage
• Effluent
• Wastewater not containing discharge from toilets.

Features and benefits

• Cable plug connection
• Unique clamp connection
• Specially designed lifting handle
• Unique cartridge shaft seal
• Modular design
• Heavy-duty ball bearings
• Short rotor shaft.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Unilift AP and Unilift AP Basic are submersible drainage pumps designed for both temporary/portable installation and permanent free-standing installation. These single-stage pumps are made mostly of stainless steel. All types are available in either single phase or three phase versions and for 50 or 60 Hz power supply.

The number in the type designation, e.g. AP12, indicates the spherical particle size that can pass through the pump.

All Unilift AP and AP Basic pumps are fitted with a plug for connection to the mains.

Unilift AP is a single stage pump with either semi-open impeller (AP12) or with vortex impeller (AP35 and AP50). All Unilift AP pumps are fitted with a stainless steel sleeve for cooling during operation. The strainer at the bottom prevents particles larger than the pump is designed for from entering the pump. The strainer is clipped onto the pump housing. All Unilift AP pumps can be supplied with or without float switch, for automatic or manual operation. Pumps with an ”A” in the type designation are fitted with a float switch. 3-phase versions have an additional starter box connected to the float switch. The outlet is positioned at the top of the pump and is available in Rp 1 1/2 to Rp 2.

An optional non-return flap valve can be fitted in the outlet in order to prevent backflow.

Unilift AP Basic pumps are single-stage pumps (AP35B, AP50B) with vortex impeller. All Unilift AP Basic pumps are made of stainless steel, with a composite baseplate. The Unilift AP Basic range is designed for submerged operation, either free-standing on the base plate or installed using an auto coupling. The pump inlet is designed to prevent to large particles from entering the pump. The base plate is clipped on by means of four clips hidden under the composite ring at top of the pump housing. The ring prevents dirt from sticking to the clips. All Unilift AP Basic pumps can be supplied with or without float switch, for automatic or manual operation. Pumps with an ”A” in the type designation are fitted with a float switch. The outlet is positioned at the side of the pump and is R 2.

Applications

• Water and rainwater in horticulture
• Water from rivers and lakes
• Rainwater, drainage water and water from flooding
• Water for filling/emptying containers, ponds, tanks, etc.
• Effluents from showers, washing machines and sinks below sewer level
• Pool water
• Ditch drainage water
• Groundwater (lowering applications)
• Domestic effluents from septic and sludge-treating systems
• Liquids containing fibres from light industry, laundries, etc.
• Effluents from viaducts, underpasses, etc.
• Drainage water from garage sprinkler systems

Features and benefits

Unilift AP is for permanent or temporary free-standing installations. Most components are made of stainless steel. Cable fitted by means of a plug. Available in both automatic and manual versions. Single-phase versions have an integrated thermal switch.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

Grundfos SP submersible pumps are renowned for their high efficiency and reliability throughout the range. Made entirely of corrosion-resistant stainless steel, SP pumps are ideal for a wide variety of applications.

Grundfos SP pumps represent state-of-the-art hydraulic design. Built to deliver optimum efficiency during periods of high demand, the SP pumps provide low long-term costs and high operating reliability regardless of the application.

The Grundfos SP range offers high efficiency, high resistance to sand and other abrasives, motor burnout protection, and easy maintenance. A complete monitoring and control system is available for constant optimisation of the pumping system.

Applications

The pumps are suitable for:

• Groundwater supply to waterworks
• Irrigation in horticulture and agriculture
• Groundwater lowering
• Pressure boosting
• Industrial applications.

Features and benefits

• State-of-the-art hydraulics provide high efficiency and low operating costs
• 100 % stainless steel inside and outside
• Sand resistant
• Resistant to aggressive water
• Motor burnout protection
• Dry-running protection
• Monitoring, protection and communication via the MP 204 protection unit and the R100 remote control.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

S pumps form the backbone of many sewage systems. They are selected for their strength, their durability, and for innovative features such as the SmartTrim impeller clearance adjustment system and the Smart Seal for leakage prevention.

The SmartTrim system used on the S-pumps makes it easy to adjust the factory-set impeller clearance and thus to maintain maximum pump efficiency.

The Grundfos SmartSeal Auto-coupling gasket provides a completely leak-proof connection between the pump and the base unit of the auto-coupling system. The shaft seal is capable of rotating in either direction. When the pumps are installed with separate pipework, sludge sedimentation can be avoided by back-flushing the system at regular intervals.

Applications

The pumps are suitable for the following applications:

• Transfer of unscreened raw sewage
• Transfer of raw water
• Pumping of water containing sludge
• Pumping of industrial effluent.

Features and benefits

• Wide range
• SmartTrim
• Operation with/without cooling jacket
• Submerged or dry installation
• Channel and vortex impellers
• Built-in motor protection
• SmartSeal
• Large free passage
• SuperVortex impeller.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Grundfos range of recirculation pumps is the product of decades of engineering experience. Created to handle large flows with low heads, the SRP models are equally suitable for wastewater treatment plants and flood control.

SRP units come in three main variants – DN 300, 500 or 800 mm, fitted with motors from 0.8 to 24 kW. The units share many features with the AMG and AFG gear-driven mixers and flowmakers, making them instantly familiar to service staff and facilitating easy maintenance.

Recent developments include a triple sealing system for maximum protection of the mechanical shaft seal and a bracket that facilitates very easy installation.

Applications

The pumps are suitable for the following applications:

• Re-circulation of sludge within sewage treatment plants
• Storm water pumping.

Features and benefits

• High efficiency stainless steel propeller
• Electronic leak sensor in gearbox/shaft seal housing
• Wide performance range
• Strong axial gear in slim design for high hydrodynamic efficiency
• Integrated overload and overheat protection
• Good self-cleaning capabilities.

PT. Andalan Inti Rekatama  –  GRUNDFOS  Authorized Dealer   – Service Partner

The Unilift AP and Unilift AP Basic are submersible drainage pumps designed for both temporary/portable installation and permanent free-standing installation. These single-stage pumps are made mostly of stainless steel. All types are available in either single phase or three phase versions and for 50 or 60 Hz power supply.

The number in the type designation, e.g. AP12, indicates the spherical particle size that can pass through the pump.

All Unilift AP and AP Basic pumps are fitted with a plug for connection to the mains.

Unilift AP is a single stage pump with either semi-open impeller (AP12) or with vortex impeller (AP35 and AP50). All Unilift AP pumps are fitted with a stainless steel sleeve for cooling during operation. The strainer at the bottom prevents particles larger than the pump is designed for from entering the pump. The strainer is clipped onto the pump housing. All Unilift AP pumps can be supplied with or without float switch, for automatic or manual operation. Pumps with an ”A” in the type designation are fitted with a float switch. 3-phase versions have an additional starter box connected to the float switch. The outlet is positioned at the top of the pump and is available in Rp 1 1/2 to Rp 2.

An optional non-return flap valve can be fitted in the outlet in order to prevent backflow.

Unilift AP Basic pumps are single-stage pumps (AP35B, AP50B) with vortex impeller. All Unilift AP Basic pumps are made of stainless steel, with a composite baseplate. The Unilift AP Basic range is designed for submerged operation, either free-standing on the base plate or installed using an auto coupling. The pump inlet is designed to prevent to large particles from entering the pump. The base plate is clipped on by means of four clips hidden under the composite ring at top of the pump housing. The ring prevents dirt from sticking to the clips. All Unilift AP Basic pumps can be supplied with or without float switch, for automatic or manual operation. Pumps with an ”A” in the type designation are fitted with a float switch. The outlet is positioned at the side of the pump and is R 2.

Applications

• Water and rainwater in horticulture
• Water from rivers and lakes
• Rainwater, drainage water and water from flooding
• Water for filling/emptying containers, ponds, tanks, etc.
• Effluents from showers, washing machines and sinks below sewer level
• Pool water
• Ditch drainage water
• Groundwater (lowering applications)
• Domestic effluents from septic and sludge-treating systems
• Liquids containing fibres from light industry, laundries, etc.
• Effluents from viaducts, underpasses, etc.
• Drainage water from garage sprinkler systems

Features and benefits

Unilift AP is for permanent or temporary free-standing installations. Most components are made of stainless steel. Cable fitted by means of a plug. Available in both automatic and manual versions. Single-phase versions have an integrated thermal switch.